Shipped by EXPRESS,Geeetech Unassembled Crazyflie Nano-quad tiny Drone Quadcopter Kit 10-DOF with Crazyradio 2.4Ghz nRF24LU1+USB radio dongle with antenna

Shipped by EXPRESS,Geeetech Unassembled Crazyflie Nano-quad tiny Drone Quadcopter Kit 10-DOF with Crazyradio 2.4Ghz nRF24LU1+USB radio dongle with antenna

Click Here !!

If you are searching Cheap Remote Control Helicopter then today you are at the right site.
Shipped by EXPRESS,Geeetech Unassembled Crazyflie Nano-quad tiny Drone Quadcopter Kit 10-DOF with Crazyradio 2.4Ghz nRF24LU1+USB radio dongle with antenna is one of the Cheap Remote Control Helicopter at the market. This Cheap merchandise delivers to you to answer your wish.
Here, we give you one of Cheap Remote Control Helicopter.

Shipped by EXPRESS,Geeetech Unassembled Crazyflie Nano-quad tiny Drone Quadcopter Kit 10-DOF with Crazyradio 2.4Ghz nRF24LU1+USB radio dongle with antenna

• Small and lightweight, around 30g and about 90mm motor to motor,3-axis high-performance MEMs gyros with 3-axis accelerometer: Invensense MPU-6050
• Light time up to 7 minutes with standard 180mAh Li-Po battery,Powerful 32 bit MCU: STM32F103CB @ 72 MHz (128kb flash, 20kb RAM)
• Standard micro-USB connector for charging which takes ~20min for the stock 180mAh Li-Po battery
• On-board low-energy radio@1mW based on the nRF24L01+ chip. Up to 80m range (environment dependent) when using the Crazyradio USB dongle,Radio bootloader which enables wireless update of the firmware
• Available footprints to manually solder magnetometer HMC5883L/HMC5983 or/and barometer MS5611 (Mounted on the 10-DOF version),Expansion header 2×10 pins 1.27mm (0.05") pitch including power, I2C/UART, SPI/ADC. Header also contains ARM Cortex 10-pin JTAG (header not included)

Please note: The list is UNASSEMBLED,you need to build it by yourself when you receive it.

The Crazyflie is a tiny quadcopter often referred to as a nano-quad, built using the PCB itself as the frame. Developed solely by open source tools and designed with development in mind.A Crazyflie Nano Quadcopter include a crazyflie and a crazyradio.

Basic concepts:
The Crazyflie is controlled from a computer using an input device such as a game controller (PS3 or Xbox 360). A USB radio dongle is used to send control data from the controller/computer to the quadcopter.

The primary stage
Packet
&& Crazyflie control board
&& 5 x motor mounts (one as spare)
&& 5 x coreless motors (one as spare)
&& 5 x CW propellers
&& 5 x CCW propellers
&& 1 LiPo batter
&& Crazyradio 2.4Ghz nRF24LU1+ USB radio dongle with antenna
Tools you need:
&& Soldering iron and solder
&& Scissors
&& Tweezers and a clamp or third-hand can come in handy
Check the electronics
Before you go ahead and assemble the Crazyflie check the Crazyflie control board and the Crazyradio electronics:
Attach a powered micro-USB cable to the Crazyflie control board. It should power up and blink 5 times with the green LED. After that the green LED should be fully on and the red LED should blink.

More information, please check our page:http://www.geeetech.com/crazyflie.html

Check Price & More Information >>>

Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on this site at the time of purchase will apply to the purchase of this product.